Showing posts with label lesson. Show all posts
Showing posts with label lesson. Show all posts

Friday, June 28, 2013

Basic Knitting handout



This is a copy of the handout I use for the basic hand knitting I use for teaching at SCA classes. Please use it, and remember to cite you sources!

INTRODUCTION TO KNITTING

BASIC ABBREVIATIONS FOR KNITTING:
·         BO- bind off
·         Ch-chain; may be seen as Ch1, Ch2, etc.
·         Circ- circular
·         Co- cast on
·         Dc- double crochet
·         Dpn- double-pointed needle(s)
·         K-knit
·         K2tog- knit 2 (stitches) tog
·         M1R- make one right slanting; with the tip of the left hand needle inserted from back to front, lift the strand between the two needles onto the left hand needle; knit through the front loop to increase one stitch
·         M1 or M1L- make 1 left slanting; with the tip of the left hand needle inserted from front to back, lift the strand between the 2 needles onto the left hand needle; knit the strand through the back loop to increase one stitch
·         P- purl
·         P2tog- purl 2 (stitches) together
·         Pm- place marker
·         Rnd- round
·         Rs- right side
·         Ws- wrong side
·         Ssk- slip, slip, knit- slip the next 2 stitches to the right hand needle one at a time as if to knit; return them back to left hand needle one at a timeto their new orientation; knit them together through the back loops
·         St(s)- stitches
·         Tog- together
·         Yo- yarn over; bring yarn forward (to the purl position), then place it in position to work the next stitch. If the next stitch is to knit, bring yarn over the needle and knit; of next stitch is to be purled, bring yarn over the needle and then forward again to the purl position and purl.


I will make sure to add different pictures at a later time...


Pot holder/arm warmer pattern
Cast on 44 stitches. Knit until desired length. Bind off. With right side facing, sew side seam, beginning at cast on edge and ending 2 1/2 “ from bound-off edge, leaving a gap of approx 1 ½’ from thumbhole. Rejoin yarn and sew seams to end. Weave in all ends

Works Cited:
26 Punk Knits

Hope you enjoy, and keep on Knitting!
~An

Detached Buttonhole Embroidery Stitch

This is a copy of the handout I use for the detached buttonhole stitch I use for teaching at Embroidery classes. Please use it, and remember to cite you sources!



DETACHED BUTTONHOLE STITCH
·         Because this stitch is not attached to anything, it can be stuffed to give a raised appearance, or be totally cut from the fabric to form the basis of stumpwork
·         The buttonhole stitch has several common variations (blanket stitch, eyelet stitch, and the detached buttonhole)
·         A filling stitch with several variations (closed buttonhole, crossed buttonhole, Buttonhole shading <top knotted buttonhole stitch, German knotted buttonhole stitch, tailors buttonhole stitch, Armenian edging stitch>)

      
HOW TO COMPLETE
WHAT IT SHOULD LOOK LIKE
I will make sure to update this as I collect more information, and with better pictures

BIBLIOGRAPHY 
¨       Exploring Elizabethan Embroidery< Dorothy Clarke , Stephanie Powell


Saturday, November 24, 2012

How to build a card loom

Here it is: the directions to building a simple card loom. This pattern should only on average cost about $17-$20 a loom. In total we made 9. We were able to get the wood cut at the hardware store, which made life a bit easier. If you have any questions, please do not hesitate to ask. If I can't answer it, then I'll hunt it down for you. I would love to find out if anyone else had the same results as us.




·         1    2ft. 1x6
·         2    6in 4x2 (can be created by gluing 2    2x2)
o   If using 2x2’s wood glue and c-clamps
·         4    5/16-18x41/2 carriage bolts
·         4   5/16-18 wing nuts
·         4   felt pads for furniture (optional)
·          Scrap leather/stiff fabric (non-abrasive) to pad loom
·         5/16 drill bit
·         21/64 drill bit
·         Hammer

1.       Sand boards
2.       If gluing 2x2’s start gluing process
3.       Cut and attach leather

4.       Drill holes through wooden blocks and main board (when dry)
a.       Use 5/16th for main board
b.      Use 21/64 for top blocks



 












5.       Add bolts and wing nuts 
6.       Add felt pads to bottom bolts
*if making multiples, mark sides for they are individualized, and depending on your drillers skills









 Sorry if the Pictures don't line up straight: I tried to get them under each set of directions. Enjoy!

~An